May 24, 2018

GSX Coordinates - BBS Airbus A320

0 comments

Below are the coordinates that align GSX with the Blackbox Simulations Airbus A320. Just input these coordinates into the aircraft settings in GSX. If you have any issues or find better coordinates, please post them in the comments. Thank you.

----- A320 -----

Nosegear Distance 10.10

Passenger Door #1 Door without open/close checks NameFront Passenger Door Custom check (L:BB_LDoorPax1,bool) Position -2.25 10.20 3.84 Angle 0.00

Passenger Door #2 No Door

Passenger Door #3 No Door

Passenger Door #4 Door without open/close checks Name Rear Passenger Door Custom check (L:BB_LDoorPax4,bool) Position -2.00 -13.70 4.10 Angle -9.00

Service Door #1 Door without open/close checks Name Front Service Door Custom check (L:BB_RDoorPax1,bool) Position 2.25 10.20 3.84 Angle 0.00

Service Door #2 Door without open/close checks Name Rear Service Door Custom check (L:BB_RDoorPax4,bool) Position 2.00 -13.70 4.10 Angle 9.00

Cargo Door #1 Door without open/close checks Name Front Cargo Door Custom check (L:BB_DoorCargoFwd,bool) Position 0.70 7.28 2.40 Angle 0.00 ULD Code BELT

Cargo Door #2 Door without open/close checks Custom check (L:BB_DoorCargoAft,bool) Name Rear Cargo Door Position 0.70 -6.90 2.40 Angle 0.00 ULD Code BELT

Deicer In Position 2.92 -0.78 3.46

Deicer Out Position 16.46 -5.28 5.04

Fuel Position 9.28 -1.64 3.80

New Posts
  • Good evening! FSAirlines seems to be crashing X-Plane. Does anyone here have Xplane/FSAirlines knowledge? or should I go to FSAirlines' forum? was 17mi out from my destination airport and the game crashed because the FSA Client switched from "descent" to "cruise" as i leveled out for approach. Hopefully someone can help me.
  • Occasionally, you may encounter an issue where the EZdok camera seems to override the controls when you are editing vehicle locations with GSX. You may notice that you aren't able to enter slew mode, and it most likely has to do with your aircraft. Try to enter slew mode to move your aircraft around the airport. If it doesn't allow you to by pressing the Slew Mode on/off key (Y or whatever key you've assigned), that is the issue you will need to resolve. In order to resolve it, reload your aircraft, and try to enter slew mode again. You should now be able to move your aircraft around with your slew keys. Now try to edit your vehicle locations with GSX. EZdok should no longer override the controls. EZdok commands should disable when slew is activated. The GSX vehicle location editor uses slew mode to edit the vehicle positions. If you aren't able to enter slew mode, then you will be unable to edit those vehicle positions, but EZdok will work as normal. That's why it will seem as if EZdok is overriding the controls. The problem isn't either GSX or EZDok, but the fact your aircraft isn't allowing you to enter slew mode. I've found this to be an issue will Carenado (unknown reason... possibly open doors) and Black Box Simulation aircraft (when ground power is connected).
  • Members, This is reference for our Cost Index Flight with duration < 4 Hours: A319 and A320 = Cost Index 27 B737-300 and B737-500 = Cost Index 45 B747-400 = Cost Index 90B757-200 = Cost Index 80 B767-300 = Cost Index 65B777-200 = Cost Index 85 Flights with duration > 4 Hours: A319 and A320 = Cost Index 22 B737-300 and B737-500 = Cost Index 30 B747-400 = Cost Index 85 B757-200 = Cost Index 75 B767-300 = Cost Index 60 B777-200 = Cost Index 80